SYN 1800MHz +30dBm Repeater 30 MHz Tele2/Telenor

Article no.: SYN-D30L-S30
Delivery time: Est. delivery 7d

SYN-D30L-S30 is a band-selective (30 MHz width) 1800 MHz repeater specially developed for Swedish requirements and wishes. Adapted for Tele2/Telenor A new generation of repeaters which is significantly smaller and more energy-efficient (develops less heat) than previous models in... read more

20 009 kr

button_wishlist

SYN-D30L-S30 is a band-selective (30 MHz width) 1800 MHz repeater specially developed for Swedish requirements and wishes.

Adapted for Tele2/Telenor

A new generation of repeaters which is significantly smaller and more energy-efficient (develops less heat) than previous models in the same power class.

This model is adapted for medium-sized offices/warehouses up to approx. 2500m2 in an office environment or up to approx. 6000m2 in very open areas. ATTENTION! All sizes are intended as an estimate only. All installations are unique and must be calculated individually.

It is configurable so that the installer can change the center frequency. In addition, the possibility to configure a number of other parameters via the Touch Screen

SYN-D30L-S30 has a built-in "Uplink Sleep Mode" or so-called "Silent Mode" that protects the operator's base stations from noise/load when no one behind the repeater is speaking phone. That is, the repeater turns off the signal to the operator's base station when there is no traffic behind the repeater. This happens in milliseconds. This is a function that is usually only found in more powerful and significantly more expensive repeaters.

The repeater normally runs in a fully automatic mode that tests signal strengths and possible signal leakage between internal and external antennas during start-up to set up the repeater and alarm if it detects potential signal leakage that could result in looping.

The repeater also has automatic shutdown in case of excessive signal leakage or looping. Everything to prevent problems for you and the operators.

An LCD display shows signal strength in and out as well as amplification factor both in uplink and downlink as well as center frequencies in Uplink/Downlink.

Normally the repeater is run in auto mode. But if you need to manually set the gain, do it with the buttons.

Regular antenna connectors (N-type) are screwed into the metal chassis to be able to connect even coarse cables.

Unique features with SYN-D30L-S30

A real band-selective 1800 MHz repeater (ie acceptable by the operators)
Very low power consumption compared to the output power
LCD Touch Display but setting of gain and Uplink/Downlink frequency
Uplink Sleep Mode - saves resources for the operator
RED CE/3GPP tested and approved.
Automatic gain adjustment
Built-in protection against round trip/self-oscillation
Automatic test procedure of antenna separation, signal strength and gain during start-up

How to find out if you can use a 3G repeater

3G Repeater FAQs and Repeater Permits

Manual PDF (English)

Settings for the different frequencies depending on operator and model

Frequency band	30 MHz within 1805 -1880 MHz / 1710-1785 MHz
	Adjustable center frequency via Touch Display
Bandwidth< /td>	Fixed 30 MHz
Mobile technology	2G, 3G and 4G
Output power	Downlink +30 dBm / Uplink +23 dBm15
Gain	Downlink 80 dB / Uplink 75 dB
Automatic Gain Adjustment AGC	> 15 dB
Auto / Manual gain adjustment	31 dB in 1 dB increments
Chassis	Metal chassis with built-in heatsink
3G antenna connection	2 pc N female
Power supply	240V AC, max 15 W
Size	150 x 210 x 36 mm
Weight< /td>	1.9 kg
Temperature	-25 to +55 degrees
IP40 (indoor)

Explanation of frequency bands

When choosing an antenna, pay attention to which frequency bands the antenna supports. Depending on which operator and where the antenna will be used, the frequency bands vary. Larger cities use 2600MHz while smaller towns use 800/900MHz with some support bands in between such as 1800/2100MHz.

A higher frequency band gives a higher speed but also has a shorter range. The same applies to the antenna, if you have a base station that transmits on 2600MHz, your antenna, antenna cable and the location of the antenna become more important than on a lower frequency band. Explanation of signal loss we will go through soon. Higher frequency bands also mean shorter range from the base station.

450MHz (coverage band) also known as the Net1 band is the frequency band that covers the most area in Sweden. Therefore, Net1 is known to be able to have reception where other operators don´t have a chance, but with low download and upload speeds. The reason why this band is called Net1 is because that the company Net1 has exclusive rights to this frequency band.

800MHz (coverage band) is used by all common operators, excluding Net1. The low frequency band means that 800MHz covers a lot of space. Therefore, the band is used outside big cities or smaller towns. 800MHz is the most used frequency band around Europe.

900MHz (coverage band) is the band that Tele2 and Telenor initially used as coverage band. 900MHz is a more unusual LTE band and in the beginning the band caused some problems when the clients (mobile phones etc.) could not connect to 900MHz. Today, the mobile phone manufacturers have adapted the mobile phones to be able to communicate on 900MHz.

1800MHz (capacity band) is the latest frequency band launched. All operators today use this band in metropolitan centers (apart from Net1).

2600MHz (capacity band) is a very well-used frequency band all over Europe. 2600MHz is the highest frequency band used for LTE, this means that the band also has the shortest range compared to 800/900MHz. Due to the high capacity, the band is used in metropolitan environments where many base stations are required to cover as much surface as possible and have as high a capacity as possible.

Frekvensplan 4G